Liquid Kicks LK SHOES Top Coat Leather Sealer Starter Pack 5 bottles 2oz each

Description

Liquid Kicks LK SHOES Leather Top Coat/Sealer Starter Pack
Finish: Flat, Matte, Factory, Gloss + Intercoat
Volume: 5  2 oz. bottles
The whole set of LK Shoes leather finishes! Get the gloss, factory, matte, flat, and intercoat all in one set!
All of the finishes can be mixed with each other to create your own level of sheen!!
LK Topcoats are the highest quality leather topcoats in the industry! Liquid Kicks designed their top coats to protect your art on a variety of surfaces such as leather, vinyl, pvc, canvas, cotton, and silk. They are extremely scratch resistant, UV resistant, waterproof, and chemical resistant. LK Topcoats give you the ability to send your custom leather, canvas, and vinyl products out into the world with confidence that they will not peel, lift, crack or fade and last! Your art will look and feel great for years.
LK Top Coats are a blend of high-performance waterbased acrylic and polyurethane resins designed for use on leather and canvas.
Preparation:
Use a clean lint-free cotton cloth to clean only the leather surface which you intend to paint. Do not excessively clean the surface. You should feel the surface change from slick to tacky as you are cleaning it. As soon as it changes feel, it has been sufficiently been cleaned. Allow the surface to sit for 10 to 20 minutes to allow solvents to escape. Do not force dry. Remove any dust or debris with a clean dry synthetic paint brush.
Applying Top Coat:
LK Top Coats should be applied with an airbrush with a tip size between .2mm and .7mm with air pressure between 25psi and 35psi or with a mini spray gun with a tip size less than 1mm. Spray top coat directly at the surface from 3 to 5 inches away with an airbrush, or 4 to 8 inches away with a spray gun. Apply top coat in e
v
en coats by working from side to side and top to bottom while overlapping each previous line to create medium wet coats. Allow top coat to dry before moving to the next coat.
Drying:
Top Coats are best air dried but may be forced dried with a hairdryer with a temperature not exceeding 350f. Air drying will take 35 to 50 minutes depending on ambient temperature and humidity. Force drying should not be allowed to exceed 10 minutes. LK Top Coats are ready to handle and use after fully drying but full chemical and scratch resistance is only achieved after 12 hours of curing at room temperature 70f.
Pot Life:
Once the product is poured into an open-air container such as an airbrush cup or mixing cup, curing will begin. A test showed that in a 1
/
8oz airbrush cup at 72f the product was usable for 2 hours before performance was affected. In a similar test in a 16oz cup, the product was usable for 6 hours. To extend pot life, keep unused portion covered with a cap or lid. The shelf life of unopened bottles of Top Coat has been proven to be longer than 1 year under normal conditions. The shelf life of partially used bottles has not shown to be an issue.
Theoretical Coverage:
One 2oz bottle will coat more than 15 pairs of leather shoes or 1 large leather car seat. Coverage on canvas will vary based on the type of canvas and size.
Storage:
Store between 50f and 80f and away from long term exposure to direct sunlight to prevent oxidation. Long term exposure to temperatures over 120f and below 30f may cause a loss of product performance. Keep lid closed when not in use to prevent drying.
Clean up:
Clean all tools immediately use with water, acetone or 4012 reducer by Createx Colors. Clean up of dried top coats requires harsh solvents such as M.E.K. or volatile paint strippers. Clean all traces of sealer out of your airbrush or spray gun immediately after use to prevent the product from drying inside the body and causing a difficult to remove clog! Rinse until cleaner no longer becomes foggy from top coat.
IN STOCK AND READY TO SHIP!
View more great items